TITEBOND COLD PRESS HPL

Titebond Cold Press for HPL is a high-quality, economical alternative to contact cement for large-scale flat laminating. It is specifically formulated for cold press laminating of High Pressure Laminates and backed veneers to solid woods, particleboard, MDF, plywood and other porous materials. Titebond Cold Press is also suitable for most veneer and panel-on-frame applications. It offers a moderate speed of set, a translucent glue line and contains none of the harmful or corrosive fumes typical of most contact cements.

Features & Benefits

  • Moderate speed of set
  • Economical alternative to contact cement
  • Dries translucent
  • Water cleanup
  • Suitable for large-scale flat laminating
  • Suitable for panel-on-frame cold press applications

Application Guidelines

  • Application Temperature: Above 50°F (10°C)
  • Open Assembly Time: 15 minutes (70°F./50% RH)
  • Total Assembly Time: 15-20 minutes (70°F./50%RH)
  • Minimum Required Spread : Approximately 6 mils or 250 square feet per gallon
  • Required Pressure Application : 30-80 psi for HPL, 100-150 psi for Panel-on-Frame, 100-250 psi for Veneer
  • Method of Application: For most consistent coverage a mechanical spreader is recommended.
  • Cleanup: Damp cloth while glue is wet. Scrape off and sand dried excess.

Bond Strength ASTM D-905 (On Hard Maple)

Temperature Strength Wood Failure
Room Temperature 2,711 psi 32%
150°F. Overnight 1,890 psi 1%

Physical Properties

  • Type: Modified PVA emulsion
  • Calculated VOC: 3.2 g/L
  • State: Liquid
  • Weight Per Gallon: 9.7 lbs.
  • Color: Off White
  • Dried Film: Translucent
  • Flashpoint: > 200°F
  • Solids: 42%
  • Freeze / Thaw Stability: Stable
  • Viscosity: 4,500 cps
  • pH : 4.9
  • Chalk Temperature: To assure a good bond, 50°F is the lowest recommended temperature of the glue, air and materials during application.
  • Storage Life: 12 months in tightly closed containers at 70°F

Limitations

Titebond Cold Press for HPL is specifically designed for laminating flexible materials and is not suited for other types of assembly applications. Vacuum pressing should only be used for veneers up to 1/16 inch in thickness. Do not use when temperature, glue or materials are below 50°F. Not recommended for exterior use or where moisture is likely. Freezing may not affect the function of the product but may cause it to thicken. Agitation should restore product to original form. Read MSDS before use. NOTE: STIR PRODUCT BEFORE USE TO ENSURE UNIFORMITY. KEEP FROM FREEZING.

Product SKUs

Part NumberUPCCase UPCSizeWeightUnits Per PackagePackages Per Pallet
46170370830461755 Gallon Pail51.58124
461855 Gallon Drum575.0514

Caution Statement

CAUTION: EYE AND SKIN IRRITANT. Contains oxydipropyl dibenzoate. Don not swallow. Do not allow eye contact or prolonged skin contact. FIRST AID: if swallowed, do not induce vomiting; contact physician. If eye contact occurs, flush eyes with water for 15 minutes. Wash skin contact areas with soap and water. If irritation from eye or skin contact persists, contact physician. For additional information, refer to Safety Data Sheet. KEEP OUT OF THE REACH OF CHILDREN.
Important Notice: Our recommendations, if any, for the use of this product are based on tests believed to be reliable. Since the use of this product is beyond the control of the manufacturer, no guarantee or warranty, expressed or implied, is made as to such use or effects incidental to such use, handling or possession or the results to be obtained, whether in accordance with the directions or claimed so to be. The manufacturer expressly disclaims responsibility therefore. Furthermore, nothing contained herein shall be construed as a recommendation to use any product in conflict with existing laws and/or patents covering any material or use.
2020 Bruck Street, Columbus, Ohio 43207
CUSTOMER SERVICE 1-800-669-4583
TECH SERVICE 1-800-347-4583
www.titebond.com

Franklin International